Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
They are making a number of great observations on Installing A Bathtub in general in this article below.
Setting up a tub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you may need a specialist plumber to make tube links.
This post will assist you install a new bath tub in your shower room if you have already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your tools and also material list must make up the following:
Planning for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water staying in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited access that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog entry about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Sharing is good. Helping people is fun. Thanks for taking the time to read it.
Maintenance Sign-Up
Report this page